Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
I stuck a breakpoint in the main loop to capture the timer values. Everything looks good, the capture has worked. The interrupt isn't called however. I've disabled the softdevice...
Please understand my low English level.
Segger cannot find be_advdata.h. I've added this route to the preprocessor. But an error occurs. How can I fix this?
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
For better clarity, I am trying to understand...
When scanning, is there a built-in way to detect and ignore duplicate advertisement packets (i.e. from the same device)? Specifically, I want to instruct the SoftDevice not...
Hi.
Thank you for your hard work.
I would like to apply the Timer example to the Uart example in SDK 15.2.0.
It was able to build without any problems before the timer...
Can somebody help me to setting up debugging in eclipse (nRF52840_xxAA)? As all I use some old tutorial here . But I still can't set up debugging on eclipse for 3 years of...
Hi
We are using the nRF9160 to drive the SD pin of the QM14501 LNA, which would typically consume 740uA. While the pin is driven high, I only measure 0.7V on the pin, so...
Hello,
I'm receiving a FDS_EVT_UPDATE (FDS_ERR_OPERATION_TIMEOUT) in my fds event handler. My update didn'it work but i don't know why.
If someone has already faced this...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
hi, I am beginner , so confused how to doing write and read sequence. I want read and write sequence with register setting .please give me how to develope logic for that.
Hi,
I'm working on a BLE link between two dev kits. For the time being, both have USB drivers and handlers that will pipe data from one USB terminal to another over BLE...
I'm having a bit of trouble getting a program downloaded onto my development board. I've been using Keil 5 to program and I haven't had a problem until I started experimenting...
I'm seeing an odd behavior where the ability for our application to communicate to peripherals via twim is being affected by the initialization values for app timers.
Timers...
HI
I'd like to clarify my understanding of how the three work-
Does the SD card library use SPI or SPIM?
Does SPIM automatically use EasyDMA, or is it configured...
