Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Dear developers,
We had a working application with SDK11 SD2.0.1 that we have migrated to SDK12 SD3.0.0. With SDK11 we could successfully bond to multiple peripherals and...
Hi. I use the nRF51882 and Arduino ide for developing. My main goal is turn on and off the Led thru the Bluetooth interface. But when I use the UART service for it I have...
I am seemingly haunted by spurious 'soft resets' I cannot seem to find a good explanation.
I have an application that is to be dormant until activated. When waking up I...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi, Nordic
I download SDK13.0.0-1.alpha_055eef3, open project
\gzll\experimental\gzp_dynamic_pairing\device\pca10040\blank\arm5_no_packs\gzll_dynamic_pairing_device_pca10040...
Is there any example of changing the default mtu size of 23 to a bigger value?
We tried increasing the att_mtu to 512, and reserved more ram for the softdevice, but still...
I have a rather unique problem. I want to control an "old-fashioned" DPDT relay using nRF52 GPIO lines. I'm trying to accomplish this task without adding a power transistor...
Hi all,
there is a nice section in here already about enabling the Reset input (P0.21). Unfortunately the link to the relevant infocenter docu is missing.
Could you...
I think that all of the Experimental is all unreliable.
I try it 5 days to test it, It always Failure.
So , I want to know that to how to understand the keyword "Experimental...
Hello developers,
I am struggling badly to use interrupt in my application. I am using softdevice S130 and ble_nus, ble_bas and ble_hrm services. All I want is to trigger...
I would like to update my current bootloader with one, that is bigger than the predefined space of the current bootloader. For that, I want to flash an application via DFU...
currently(sdk_12.1.0_0d23e2a, s132_nrf52_3.0.0_softdevice), nrf52832 can't pairing with windows 10.1607(build 14393.479), if we set lesc bit in ble_gap_sec_params_t.
windows...
Does any one has successed in doing DFU with OpenMesh? I have done all the steps according to the guide ( github.com/.../dfu_quick_start.adoc) but failed in the last step...
