I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi,
I was working with the SPI interface of nrf52DK microcontroller boards and wanted to know if there is a way to change the timings of the low and high levels of the Slave...
I'm designing a solution based on a series of nodes that senses data and has to send it wirelessly to a hub. Each hub must be able to receive data from about 4 to 8 nodes...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Please tell me the operation when garbage collection is executed. The setting values of FDS are shown below for reference.
We...
nrf52832 master wakes up the slave under sleep?nrf52832 slave wakes up the host under sleep?
My boss wants very low power consumption. I think the host can wake up the slaves...
Hi,
When I used the same command, I was only able to read the 5 bytes correctly. The Most higher byte does not match.
C:\Program Files\Nordic Semiconductor\nrf-command...
Hi
I would like to know if it is possible to to run the Nrf905 chips on 5v logic level without damaging the chip ? i see many people playing with arduino and these chips...
Hi, my customized board was using nRF52840 with 15.3 ver SDK.
And we want to make the DFU download process part can progress in the application.
(such as background download...
Hi Sir
I have used sdk 11.0.0 to develop my bluetooth application but i am facing some issue, so want enable debug logs, but i am not getting where to enable it plz help...
Hi!
I'm interested in trying out hci_usb sample of nRF Connect SDK with Nordic's Link Layer.
With following changes to application configuration I'm able to compile the...
Hi there,
I am trying the asset tracker example on nrf9160DK-HW 0.9.0.
While I have been able to get GPS fix within 20-30 seconds using the "GPS sample" example... I've...
Hello, I am starting to upload my code to some new Raytac MDBT40 modules, and am starting with the soft device of course.
I am using uVision V5.28.0.0
I can not upload...
We have devices that we want to turn on at some future date. This means that when they're deployed they should somehow get real time, calculate when they will wake up, and...
I am seeing that the default manufacturer BLE is defaultly F5:41:36, received experimentally from inspecting data from the nRF52832... Now, of course there is sd_ble_gap_address_set...
Hi,
I have a custom Nrf52810 board. It was working fine and was advertising well. Somehow ble chip got damaged and I needed to replace it.
After I replaced, I can do debug...
I would like to use Uart with low standby power consumption. and I have read this post which recommend to use libuarte:
https://devzone.nordicsemi.com/f/nordic-q-a/53880...
