hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Sorry this is very basic. Not really for NRF connect for Desktop. But for NRF connect for IOS.
1.I'm just trying to have my iPhone (iphone 6 , IOS 12.4.6) use NRF connect...
I am implementing the BLE buttonless DFU
SDK 14.2,
GCC compiler
softdevice 5.0.0
While writing the firmware data I am getting this error 00> INFO: ../../components...
Hi
I merged the AGPS to serial_lte_modem slm_at_gps.c but it did not work:
1, if I activate LTE in gps_thread_fn(), it will be failed in supl_session();
2, If I activated...
I am trying to read through the nordic 52832 i2c an accelerometer datum lsm303dlhc using the example "twi sensor".
The code used is written below.
Unfortunately, the code...
SDK: 15.1 SoftDevice: S132, v6.1 IDE: Keil Hello I am using the nRF dongle combined with nRF Connect on my PC to connect to my BLE peripheral (custom board). During connected...
Hi there,
I am trying to update the advertising packet (specifically update the battery service value).
I cannot make it work and the function return an error.
Has this...
I want to make serial connection in between an nRF52833 and a LPC1752.
When I use the UART in a firmware without using the SoftDevice for Mesh 4.0.1 , everything is working...
Hi,
I am using a Linux Host to communicate with my nRF52840 as a USB CDC ACM device. As a test, I ran minicom and was able to transfer bytes to my Nordic app successfully...
Gentlemen:
I'm new to Nordic processors, but I have implemented projects with Silabs Gecko and ATTiny processors in the past. I'm working on a project for a consumer product...
Hello,
I have installed Embedded Studio and acquired a Nordic license. However the Tools/Options... nRF Connect menu option does not appear. I tried creating a dummy Nordic...
The project for nRF51822 was developed on base of example ble_peripheral ble_app_hrs for pca10028/s130 with an additional vendor specific service with 128-bit UUID for an...
I have a strange problem. We built 100 custom boards. I've only checked about 50 boards so far. 47 boards work properly. 3 do not.
We used secure_bootloader_uart_pca10056...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
I am new to BLE and I am exploring Introduction to service. However I am stuck with Step 1 and Step 2. Is Step 1: static ble_os_t m_our_service; (to declare a service) and...
