Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi, I am a beginner, during my internship I need to evaluate the nRF9169 DK for cellular applications.
I successfully implemented the communication over serial by using...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I'm using NRF_WDT and it works very good.
I would like to investigate my project failures and I want to save some data when watchdog is expired.
How can I catch...
I am newbie here. I was reading ‘Introduction to Nordic nRF5 SDK and Softdevice' dated 15 Jan 20. The softdevice naming rule establishes Sxyz
wherein z – denotes the SoC...
Hi,
We're noticing high power consumption when the 9160 is supposed to be PSM sleeping in borderline signal locations that is breaking our power consumption model, reducing...
The docs say:
Once configured, it is possible to perform cryptographic operations using the the CRYPTOCELL subsystem where KDR is selected as key input without having access...
Running nRF Connect SDK v2.1 targetting an nRF52840 DK (PCA10056)
I'm looking at the OTA DFU options for this SDK. The host side tool if i'm not mistaken is a go utility...
Hello,
I'm trying to integrate Mesh 4.0.0 into a program built with SDK 16.0.0 but I'm running into some issues including the correct files from the Mesh SDK. I followed...
Hi Sir,
In the datasheet of 52840, we know the DEC1 is 1.1V, DEC2/4/5 are 1.3V, DECUSB is 3.3V.
When measuring these pins, we may not get a precision value, like we got...
Hello,
I am developing an application to scanning a device continuously in nrf52832 chip. My concern is that when the device scan the other peripherals it consume a lot...
Hi,
Can you please give a brief idea which softdevice and SoC we should use as per our requirements.
1) The device should be able to connect to the mobile phone(mobile...
I am not able to build in release mode where as in debug mode builds. Even when option for release is chose , it builds in debug mode. I am using Segger Embedded studio 4...
We are using a BLE module EYSHSNZWZ from Tayio Yuden which contains the nRF52832.
using SDK 15.0.0_a53641a and Softdevice and Softdevice s132_nrf52_6.1.0
The application...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I need to use a custom board with old nRF51822 rev.2 (QFAAG0). The compatibility matrix indicates S110 Softdevice SD5.2.1. I found only 7.3.0 or 8.0.0 and there is no...
