I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I want to use a timer to generate an event at a rate of 16kHz. So just as a test I'm setting up TIMER4 and a CC event to toggle a gpio pin. As I understand the clock source...
Hello everyone,
I set up Thread Secure OTA DFU Example by using a nrf52840 DK as DFU server and a nrf52840 Dongle as DFU client. I am using nRF5 SDK for Thread and Zigbee...
I'd be grateful for some assistance with what I may be doing wrong.
I have programmed the serial example on a device and the server example on another device.
Copied the...
Hi everyone:
I was testing the bonding with passkey entry, but it seems failed.
The slave 51822 EVK board is set with "BLE_GAP_IO_CAPS_DISPLAY_ONLY" and "MITM = 1".
...
Hello devzone! I am using translation.
I am using a DK board (PCA10056) to examine the current consumption of nRF52840. I commented out the advertising_start() of the SDK...
Hi, I'm trying to implement a mesh serial node with LPN capability, where the UART can be disabled to save power, and then re-enabled via a GPIO.
I am measuring current...
Ok -
I've been through this a few times and read the forums, but the current build system is broken. I'm trying to compile (not even load the board at this point) the ble_hts...
Whichever input channel I select, I always get a value close to zero. Here is my test code using VDD as the input source:
In this case, RTT reports that the value...
More of a plea than a problem. When I migrate to a new version of the SDK I try to be very careful. So, I use sha256sum to check all similarly named files from one version...
Hi,
I am trying to read the SFDP (Serial Flash Discovery Parameter) register of a Micron NOR flash memory using nRF52840 QSPI peripheral. The read SFDP register op code...
Hello,
i work on nrf9160 dk
I would like to know if it is possible to use an AT firmware to be able to easily switch to LTE-M, NB-IOT, send sms, switch off the modem...
Hi.
I am using nRF52840 & SDK 15.0.0.
I set the advertising slow timeout to 14 min, But, the advertising stops at about 3 min.
The followings is summary of advertising...
Hi all,
I'm using nRF52 DK.
I'm developing a program based on 'ble_app_uart_c' example with custom UUID.
When I type command using UART, central device send signal to...
HI, I have following errors while building a project in segger embedded studio:
1. 'TIMER1_INSTANCE_INDEX' undeclared here (not in a function)
2. 'TIMER2_INSTANCE_INDEX...
