We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi Team,
We are porting from NRF52840 to NRF52832, what porting steps we need to take care for this in terms of,
1, In 52840 we have used the CRYPTOCELL — ARM TrustZone...
Hi all,
I'm currently working with the nRF5340 PDK trying to get the UART central sample working with a paired nRF52 PCA10040 DK running the UART peripheral program.
...
Hi,
In our existing project, it has a Bootloader and MBR, but no SoftDevice. Transport is UART for DFU.
I need to port the Bootloader to work on another project that uses...
We are wondering how nrf9160 modem decides which band to use when there are multiple bands available (LTE CAT NB) and there isn't any apllied band lock from the software side...
I've been working with the nRF52840 WLCSP package for a month or two now, and in many ways it's a great compact chip. However, as my projects require more and more pins, I...
Hi guys, Im now developing my custom board with nRF52832 based on the reference schematic below. And using Keil uvision for a programming my board.
The final objective of...
Hi
I have two custom build boards based on nRF9160-SICA. Both boards also have a nrf52840 running application code. The nr91's are running identical firmware (slightly modified...
Dear.
Now Im testing the nRF24L01 to develop a module.
Using this, I want to know the receive power.
nRF24L01 has a registef to use similar function. Register...
Hi,
I'm trying to write firmware for the nrf52840 that reads from a sensor and then sends data to a PC over BLE. Ultimately, I need the BLE link to achieve ~ 1.1 Mbps throughput...
Hi all,
I observe a connection supervision timeout (HMI error code 0x08) in my Nordic firmware with certain Android smartphones (controller).
Additional info regarding...
Hi. I'm just wondering if Nordic Semi engineers have done any tests with standard beacons (any particular beacon interval and test condition) application and compared current...
Hi teams,
We made BLE mesh custom boards based on nRF52833.
These nodes are configured to send broadcast messages for every 10 seconds.
Currently, these boards uses...
Hi Sir,
We would like to use the Radio test to do the basick TX/RX test in SDK 15.2
We use the nRF52840-DK for test and follow the CLI document .
1. We use two board...
Baud rate 460800, error code NRFX_ERROR_INTERNAL(1) occurred when the serial port received data。
I want to know how to avoid this problem, the current transfer rate is less...
