Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi! I have tried to use USB CDC ACM in my project but after running the USB CDC ACM example in the SDK, I found out that the example have the issue of not sending the data...
Hello,
So I'm constantly reading data using i2c into a variable. How do I transfer the data in this variable to the pc? It's just an array.
I understand that I have...
I am looking for a smallest size transceiver with an antenna done as part of the PCB layout (no external antenna needed). The simplest RF PCB layout is preferred, single frequency...
Hi, I purchased a Sparkfun Breakout board for the NRF52832, but the bootloader on it seems to be extremely unstable. Hence, I've decided to flash the NRF52832 directly from...
Hello,
I already checked below link, but want to clarify the limitations of how many concurrent sessions are allowed in Soft Device initialize.
devzone.nordicsemi.com...
Hello,
i add a new custom service with one characteristic that allows me to send values over BLE with nRF connect, but i must send some acceptable values (-2, -4, 0, 4, 10...
Using SDK14.0.0, nRF52832, GCC, GDB/Ozone, secure DFU
This question seems to get close to asking about my problem.
I am trying to debug my application with a loaded...
Hi,
We made a custom PCB using the NRF52832 and followed the reference design. While everything else is working in our system, the BLE part is not working. We are using...
Hello,
I try to develop an application on a nRF51802 device. But this device is not managed in nRF_Drivers.4.0.0-2.alpha.pack from Keil software.
Is there an update...
Hey guys! Like the title says, I'm looking for the best way to send values like humidity and VOC from the Nordic Thingy to the cloud. I have already set up the thingy to send...
Does anyone know of an off-the-shelf hardware and software that will let me read and write nRF52832 devices that are using the NFC Type 4 Library? We've tried the ACS ACR1252...
Materials publicly available say the chip works from 3.1 volts.
But is this the absolute minimum voltage or will it be possible to use also LiFePO4 battery cells with the...
I'm trying to set PWR_UP bit to 1 for the device to go into standby-I mode using STM32F103RBT6 and HAL libraries.
I send (0x20 | 0x00) command (write_reg | config reg)...
I'm trying to compile the S332 example project ble_ant_app_hrm_pca10040_s332.uvprojx. I'm using the V12 SDK and Keil uVision V5. When I try to compile I get an error saying...
