Hello,
I have been having some issues with the nRF Connect vscode extension around the flash button.
To give context, I have 3 SDK and toolchain versions installed on...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
The nRF52832 devices have been produced in hundreds of units. Currently, it has been found that individual central devices are problematic – connecting to peripherals often...
Dear everyone,
I'm currently working with the nRF7002DK and attempted to build and flash the following project from GitHub: MQTT over WiFi nrf7002DK
However, when building...
Hi, I have cloned the channel sounding with range requestor samples but every time I try to build it I encounter the error:
I have not changed the code or anything, but...
Hi,
Is it not possible to import a key which can be used for multiple use cases?
I would like to import a single key which can be used for HMAC & HKDF.
Is the below...
I am looking at the ble_app_hrs_c example (with the s130 soft device on pca10028 dev board). I have set the m_scan_mode to BLE_WHITELIST_SCAN to enable whitelisting. In the...
I have implement the systick with the idea to use it for delay functions.
The systick is running normal if no BLE Events occur, but during a BLE event it seems to be stopped...
Do conditional breakpoints work in Keil uVision5? I open the Breakpoints window and see:
If I set count to any value, I application still breaks on the first pass. When...
Hi
I have problem make the examples in the SDK 11. I get at "No rule to make target"
C:\konskimo\NYII\Spec\nRF52832\nRF5_SDK_11.0.0_89a8197\examples\peripheral\blink...
Hi,
when using timeslots I cannot turn off the external crystal that causes an higher consumption.
I already read this post and tried to turn off the timer0 (using STOP...
Dear Sir,
I merget (Software Device) + (DFU bootloader) + (Application firmware) into PE280_WS.hex
And use the script <<nrfjprog.exe --program PE280_WS.hex>>
it reported...
I'm having trouble building the ble_app_uart example in: SDK11/examples/ble_peripheral
My build environment is:
Ubuntu 15.04
SDK 11.0
GCC
S130
PCA10000
nRF51822_xxaa...
Hi,
I have a pretty hard time to get I2C/TWI running on my 52832 Dev-board (pca 10036).
My problem is, that i do not get any physical I2C signal out of the board's pins...
Hello, this might be a silly question, but i've seen various Nordic examples and i don't know whats the difference?
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS...
nRF52 series compatibility matrix says that you can get the IC revision using nrf_ic_info_get but it is only implemented for nRF51. Does the following patch add support? ...
I am attempting to follow the BLE UART tutorial and everything seems to be going well until I fire up termite and try it out. My phone successfully recognized and connected...
hello,
Every example of nordic is done with only one main.c file , i want to have a
separtate new.c and new.h file and take all the code from main.c and put it to
the...
Hello,
I am using SDK version 9 with softdevice s130 operating as both a central and peripheral. I provide a custom peripheral BLE service, and when it receives some information...
Hello,
I tried to use the example of SPI slave with the sdk 10.0. But I have an issue: the character "Ignored Transaction" is send on MISO pin.
I would like to now why...
Hi, I'm somewhat confused about using GCC, since I don't want to use Keil.
I'm using nRF51 DK.
I see makefiles in the example subdirs of SDK, but I would expect at least...
