Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
HI Nordic,
I am trying to add OTA-DFU feature to my application. I am able to perform DFU, however the DFU is not working properly always.
First I flash the softdeivce...
Hi,
I am using wireshark with nRF52 as a sniffer. While searching for advertising devices a bunch of same type of BLE devices are not detecting by nRF52 as well as I also...
Hi Nordic,
I'm looking at the PM_EVT_FLASH_GARBAGE_COLLECTED event in SDK14.2 and have noticed that it is generated even if garbage collection fails. Currently no error...
On SDK 14.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
We are using SoftDevice: sd132 v 5.0.
With event "BLE_GATTS_EVT_EXCHANGE_MTU_REQUEST", the function "sd_ble_gatts_exchange_mtu_reply" always return with "NRF_ERROR_INVALID_STATE...
I am using Fansttel BT832X SoC with SDK 14.2 ( Soft Device Version S132 5.0 ). i have configured PA/LNA mode in BT832X module. If i use only BLE advertisement i can see the...
Hi,
We want to update nrf52832 via uart. We have host controller and want to upgrade nrf52832 through it. We have SDK BLE_2.0.1 for the mesh. I had gone through DFU Example...
Hey,
I have a smart kettle Redmond RK-g201s, which is controlled by bluetooth. I have read that it has nrf51 SoC. It has 1 service with 2 characteristics: for read and for...
Hi Nordic:
I want to consult one question about "BLE HID Keyboard". I am trying to use the product---nRF52832 to make the "BLE HID Keyboard".
Then I download the source...
Hello Nordic Team,
I have some issues with the PPK since i uptdated nrfconnect from 2.0 to 2.4.
I get this error message when I try to select the serial port on Power...
I have some working knowledge of Android but I'm new to Fragments, Injection, Binding, ButterKnife .etc. I have gone through some videos and tutorials but can't catch where...
Hi,
I am using the nRF52832 DK for connecting and collecting the data from multiple beacons simultaneously. Right now i use the nRF_Connect desktop application for collecting...
Hi,
We have a nRF51822 project based on ble_app_hids_keyboard, SDK 12.3. When using Keil, it runs well. However, when using arm-gcc to compile the same code, something wrong...
Hi,
I am currently exploring the USB_CDC_ACM examples as well as the NFC record launch app.
Individually, I can make the examples run fine.
Then, I tried to combine...
Using nRF52840 SDK 15.0.0 with SoftDevice
I am trying to protect the Access Port, used to do it using the following command
nrf_nvmc_write_word(NRF_UICR->APPROTECT, 0xFFFFFF00...
