Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi all,
I have been looking for the DFU library in objective-C, without any dependency manager such as cocoapods or Carthage (we cannot use them in our solution), but...
I found the thingy hardware files and I was wondering if one can buy the flexprint antenna from you or if you can connect us to your manufacturer.
We are planning to use...
The developer kit is impressive, and I was able to get a test app running quickly using the UART thru the USB connection. However, the example BLE apps feel a great deal like...
SDK14.2 nRF52832 No SD present (using the nrf_fstorage_nvmc backend)
Question 1.
I was reading the source code for the nrf_fstorage library and saw this comment in the...
hello Nordic Team
i want to create a service ,characteristic and send data(mpu9250) over characteristc .I am using nr52 DK and mpu9250.can anybody suggest how to create...
Hello Nordic-Team,
i made a custom pcb that is based on the reference schematic of the nRF52810 QFAA with dcdc setup. However, i read that in general, the nRF52810 and nRF52832...
I would like to connect the Android Things NXP Pico board to the Nordic Thingy 52 using Bluetooth and get all sensor data from the thingy.
The Android Things board will...
Hello
Recentlly, our application with android device and nrf52, we need to do pairing process with android device in order to read characteristic from nrf52. The pairing...
I am using PCA10040 devkit and SdK11. Our application is to advertise at an interval of 100ms. Also, our application wants to spend most of the time in sleep mode. Currently...
hello , i am trying to imblement system off or system on in one of the ble central example 'ble_app_blinky_c' , i tried to refer to this example 'ble_app_template' but if...
Hi all ,
I am beginning with DFU . I complete bootloader_secure_ble and can update new firmware (application) to my NRF52832 kit via Android . And now, I have 2 kit NRF52...
hi team,
i am wondering that lot of questions regarding gps and wifi interface with nrf52 is there. why nordic is not supporting with libraries and examples for gps and...
Hi there,
I read that the nRF52840 has a maximum data throughput of around 1.3~1.4Mbps . I also read that when configured as a central it can support up to 20 concurrent...
Hello,
Can anyone point me to a good example for Polling mode using serial library?
I'm looking for an application in which I can poll the serial port for data. I went...
