I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi
I have a brief question to which I'm not able to find a clear response: When the SD send a notification of a change in a service value, this notification has a confirmation...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Hello,
As far as I can tell, the NUS app sends a signed char of value -127 to 127 in decimal. Is there a way to use the stock UART application to send an unsigned byte...
Hi Noridic,
I follow the Application note Nan_36 and download the nrf51-ble-app-lbs project as a practice, but the compiling is not smoothly with SDK 9.0. I finally fix the...
Hello,
I am working with S110 stack and the custom application. I wanted to use the ADC driver with blocking and interrupts enabled. But the application is blocking and...
Hi, I use NUS quite alot with the following condition;
(SDK 7.2 & S110 7.1 with IAR 7.1)
When the peripheral only uses NUS, iOS cannot detect the peripheral at the ...
Naive follow up to What is NUS? .
Is NUS merely a vehicle for tutorials and fast prototyping? Or can it be used to build real world apps on?
If so, do we rename the...
Hi All,
We are in design phase of our project . We would like to use NRF52832 for our project.
Our project is a wearable based on BLE. We are planning to use RTOS in NRF52...
I am starting to port the example
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_peripheral\ble_app_hrs to my board. I haven't made any change to the example to save something...
Hello, I have a problem when I attempted to increase timeslot length with 10 ms ,every time I received NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_FAILED signal.
Why can't to extend...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE.
If the program is wrong,The chip will reset,
I want to save some data to the FLASH area before the chip reset.
What I need to...
nRF 8001: How to use it in Beacon mode where in no pairing or Bonding is required and
it only transmits some information which cn be received by any phone that comes in range...
Hi.I had been confused with parameters of sd_ble_gatts_characteristic_add( ).If I set parameters
like that:
static uint8_t ast_notify_char;
..........................
