I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Good afternoon,
I have been doing some tests with the nRF SDK for Mesh v1.0.0, and have a question regarding it.
I'm using a fw based of the Light Switch example, to...
By using the DFU to transfer an updated version of the application, The nRF Connect tool pop-up tip:"upgrade succesfully". But the version of application mostly is still older...
Hi all,
I have been looking for the DFU library in objective-C, without any dependency manager such as cocoapods or Carthage (we cannot use them in our solution), but...
I found the thingy hardware files and I was wondering if one can buy the flexprint antenna from you or if you can connect us to your manufacturer.
We are planning to use...
The developer kit is impressive, and I was able to get a test app running quickly using the UART thru the USB connection. However, the example BLE apps feel a great deal like...
SDK14.2 nRF52832 No SD present (using the nrf_fstorage_nvmc backend)
Question 1.
I was reading the source code for the nrf_fstorage library and saw this comment in the...
hello Nordic Team
i want to create a service ,characteristic and send data(mpu9250) over characteristc .I am using nr52 DK and mpu9250.can anybody suggest how to create...
Hello Nordic-Team,
i made a custom pcb that is based on the reference schematic of the nRF52810 QFAA with dcdc setup. However, i read that in general, the nRF52810 and nRF52832...
I would like to connect the Android Things NXP Pico board to the Nordic Thingy 52 using Bluetooth and get all sensor data from the thingy.
The Android Things board will...
Hello
Recentlly, our application with android device and nrf52, we need to do pairing process with android device in order to read characteristic from nrf52. The pairing...
I am using PCA10040 devkit and SdK11. Our application is to advertise at an interval of 100ms. Also, our application wants to spend most of the time in sleep mode. Currently...
hello , i am trying to imblement system off or system on in one of the ble central example 'ble_app_blinky_c' , i tried to refer to this example 'ble_app_template' but if...
Hi all ,
I am beginning with DFU . I complete bootloader_secure_ble and can update new firmware (application) to my NRF52832 kit via Android . And now, I have 2 kit NRF52...
hi team,
i am wondering that lot of questions regarding gps and wifi interface with nrf52 is there. why nordic is not supporting with libraries and examples for gps and...
