I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi,
I have 3 nrf51822 devices. Two of them act as peripheral and one acts as central. Each peripheral is used in a wheel and they are the 2 wheels of a cart. Central is...
We are trying to connect RF51822 with RaspberryPi over Bluetooth. Our aim is to get Light sensor values(lux).
Please advise how to get started with RF1822 Sensor.
*) How...
Hi there~. I tried Nordic's FFT example (SDK 14.2) with a PCA10040 board. So I tried to add that FFT related codes in the heart rate peripheral example. I use the Segger's...
Hello, I am practising and studying the beacon example on nrf52840. While reading the main code, I try to delete the log_init part, however the kit doesn't advertise. I am...
Hello, I hope to realise a scenario that, my kit(nrf52840) advertises certain information, all the mobiles nearby (with BLE) could receive the information. I think the non_connectable...
Hi,
I'm looking for mBed OS 5 examples I can run on the nRF52-DK. At the mBed GitHub, I only found a Blinky and a BLE sample. I'm wondering if you are familiar with more...
I can see that there is one example for UART and it uses application uart module (APP_UART_FIFO_INIT ...). I used this module for printing strings on terminal window, but...
Hello,
I have been working with a nrf52DK PCA10040 V1.2.1 on SDK 14 without a softdevice and I have encountered a problem with a TWI sensor.
I have a TE MEAS MS5611...
Hello,
my usecase is the following: I'd like to use SoftDevice for BLE Advertising / Scanning - every now and then I'd like to "pause" BLE for a few miliseconds and send...
I download the demo project \nRF51_SDK_8.0.0_5fc2c3a\examples\peripheral\uart\uart.uvmpw to my nRF51-DK board, but uart didn't work,all 4 LEDs are on. Is there any mistake...
Finally, I managed to compile ble_beacon in segger.
However, here's what I can not understand.
Using either Segger -> Target -> Download File
or RKNRFGO I managed to...
I got beacon which use nRF51822.
I need to get radiated pattern diagram as attached picture.
this is to get KC certificate.
How can I get information? beacon maker...
Hello,
I'm using a module based on the nRF52810, the Fanstel BT832A. I'm running the basic "ble_app_beacon" firmware from the "nRF5_SDK_14.2.0_17b948a" SDK with a few changes...
I spent a few hours trying to change the base UUID and handles of the attributes of the Blinky peripheral app, just the one service and the button and LED characteristics...
I have couple of nRF51422 boards, nRF5-SDK-for-Mesh (v. 1.0.0) and good will to demonstrate some simple multihop mesh.
And I want to write some data to the flash, but operating...
