I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
Hi,
I am using nRF5182. Kiel is the IDE. I need to operate the device in 25Mhz. How can i change the clock frequency to 25Mhz. Is it possible? Will it affect the operation...
Hi,
I just stumbled upon the nAn-36 note ( www.nordicsemi.com/.../80193304 ) and I have two comments about it :
I think it's the best technical documentation I've...
Where to find definition for INTENSET/CLR for TIMERs in 'nRF51_Reference_manual v1.1'? I think I've read it all by now, but still can't find it.
After some digging I found...
If I have the PC insert 1msec byte spacing between data bytes sent to the NRF51422, it receives the message and doesn't reset. I can send messages less than 10 bytes to the...
my code shows here: github.com/.../main.c
uart_init();
printf("\r\n\r\n");
printf("\r\n __DEBUGGING__\r\n");
every time my app started, it always shows corrupted...
Is there any more information available on a release date for the next rev of the 51822 which is supposed to have better handling of concurrent A/D and radio operations? ...
C++ BLE_API of mbed, which I want to use offline with Keil-MDK, looks really well-thought & coherent to me, but I am not a guru in SW development.
Since the mbed-platform...
The NRF51822 PWM examples I have located work by toggling GPIOs. Does the device have a more sophisticated mechanism than this for generating PWM signals? More pecifically...
Hi all
In my application where I'm using the Soft device 6.0, I have a simple function which is very time critical. However, this function is not called very often, but...
Hi,
Please can you send me the ble_app_uart source code as it is missing from the latest 6.1 SDK.
I have the PCA 100003 & PCA10000 boards.
Many thanks.
Hi,
In my application I use 5 devices and 1 host to communicate.
I have only a few packets to transfer so the data rate can be low (22Byte/transmission).
The devices...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
I have implemented a boot loader for DFU based on the sdk v6.1 DFU project.
After a when an upgrade is triggered within the application soft reset by the application:
...
Any idea how I can control the TX power within the Timeslot API in SDK v6 SD110 v7?
Are there something similar to "sd_ble_gap_tx_power_set(tx_power)" in the Timeslot API...
