hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
Hi all,
i development a FW with a low power and when i measure the power consumption using a nrf connector on evaluation board i have 2 ua, and it's ok. Now i have the some...
So I can see the "API Reference" documentation on the UART driver in the info centre, however this is all very low level and I am going to waste hours going through all this...
Are there any changes required to run the Sample Bluetooth Low Energy (BLE) applications from nRF5 SDK v14.2 when migrating from nRF52840 IC Rev A to Rev B? I have followed...
Hi,
I am using the nRF52832 on a custom PCB and I am interfacing it with a flash memory chip through SPI.
I am testing the SPI communication using the spi example (nRF52...
Dear Sir,
1. The HFXO crystal can be with load capacitance 12pF? or 8pF is better?
2. According to the datasheet, "17.1.1 64 MHz crystal oscillator (HFXO)"
there is...
Hello,
we have two custom boards with nRF51822.
We use NUS.
If our pakets under 23 Bytes everthing is fine ....
If we want to sent paket with 140bytes, the central...
Hi!,
I've made a custom board using Taiyo EYSGCNZWY bluetooth module, to be used as central in a project. To use this module, several changes have to be made in the clock...
Hi,
I am using nrf52840 to verify a signature using RSA and cryptocell c310.
I get error 0x07 when I try SaSi_LibInit();
My rndContext and the buffer are both declared...
Good afternoon.
I have bought a "nRF51822 Bluetooth Smart Beacon Kit (nRF6930, Rev 1.3.0)" this is the first time I work with this, docs say that it has installed softdevice...
On the current version of the nRF5 SDK we could only use up to 3 instances due to the hardware limitation on the Engineering A of the silicon,
nRF52840 Engineering A
...
.
Included an example picture, not at all the only issue. Using the new DevZone on iOS isn't a great experience. New devZone I think will be a lot better for everyone...
hi, i am using pca10040 devkit as multi-link central device to connect with 8 nos thingy52.
i am using sdk14.2.0 multi-link central example with soft device S132v5.0, i have...
