I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
I am using nrf51822 with s110 softdevice. My goal is to allow pairing and bonding to a single central device. Once its paired and bonded, it should not allow connection and...
In one of our projects the nrf51 shares the SPI to a device with an STM32 microchip. To be able to successfully share the SPI channel, I'd have to put the SPI pins of the...
Hi,
I am currently using nRF5_SDK version 11.0.0.
I have 2 nRF52832 development kits.
On the soft device side, i am using S132.
My understanding is that this (S132...
I want to make a blinky program from scratch and have no idea how to settup keil. I would prefer something step-by-step. I have been able to use the precompiled example, but...
Hi all!!!
I'm new in here.
I'm reading document with link: developer.nordicsemi.com/.../index.html
In Figure 1, I see a phare: "IoT Device". Is the "IoT Device" nRF5x...
Hello,
my setup is nrf51822, with SDK 10.
I try to create application to drive I2C components and I get compilations errors:
In function 'Hal_I2cInit':
../../../nrf5...
I notice that Gazell could only send 32 bytes per Payload in nRf51 series. So i wanted to know what can be the maximum speed i can attain using that payload.
Hi,
I would like to test the maximum efficency build, with settings like this :
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL...
My code is as follows:
APP_GPIOTE_INIT(4);
retcode = app_gpiote_user_register(&gpioID, 0, (1 << INT_PIN_MAXIM), interrupt);
The latter function call seems to fail with...
I have check the mesh feature on below link:
github.com/.../nRF51-ble-bcast-mesh
But it seems to work under SDK8.0, how can I make it work with SDK11 and SD130?
Thanks...
To all,
I looked through the nRF52832_PS_v1.0 product spec and I can't find any power consumption numbers for Flash erase. Does anyone know what is the Flash peak current...
I'm trying to migrate a BLE peripheral app on nRF51822 from SDK 10 and s110 to SDK 11 and s130.
I saw that the new Peer Manager does away with pstorage in favour of fstorage...
