Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
We need to sample two digital inputs GPIOs at rate of 100khz-1mhz. How can we do that?
The QDEC is only good for up to 128us (~7khz) which is too slow for us.
Is there a...
I'm not able to get clear/un-corrupted data across the ttyACM on the nrf52840-PDK. I must be missing something, seems like this would have been solved a million times, but...
I recently experienced an issue with a race condition between peer manager and FDS in SDK 14.2 which was resolved under this case:
https://devzone.nordicsemi.com/f/nordic...
Hello,
I develop entirely on Linux and I am unable to find the --sd-req / --sd-id required for generating a dfu package zip using nrfutil . I am using developing for the...
I defined custom service (NRF51822,S110) to send sensor data. Code follows. Here I enabled notifications for new data. I can able to receive data, if I enabled notification...
Hi,
I have the following set up:
The remote: nrf51822 acts as central
The wheels: Each wheel has nrf51822 acting as peripheral.
The remote needs to first connect...
My application needs to be notified of large current draws due to the activity of the nRF8001. The active signal works fine for this purpose, but why is it available only...
What is the typical expected receiver sensitivity when performing BER test (1Msps, 16 byte packets) of the radio module ? The spec refers to 2 values: -93 and -96 dBm (p.231...
Hello,
We are considering merging the Eddystone and iBeacon features together, packet types toggling at each interval tick, then we assumed that we should take the Eddystone...
My device is sending a beacon under DEBUG, but not under RUN.
The issue started when I converted the scan_and_forward example to use a 16-bit device address.
It steps...
Dear Sir or Madam,
I'm using a dev kit with the nRF52832 to realize a project in school. So my work contains two wearables and both include the nRF52832. Now I want to communicate...
Hello,
is it somehow possible to calculate the distance of a BLE enabled and advertising periodially cell phone to a turnstyle gate.
There are for example 10 turnstyle...
Hello,
I'm trying to update from Mesh SDK 1.0.0 to 1.0.1, I've followed http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v1.0.1/md_doc_getting_started_how_to_nordicSDK...
Hi all,
I would like someone give me a suggestion about timers.
in my current approvement I am using an RTC timer with 32k crystal to control my sleep times it is power...
