How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Once GPIO is pressed (shorted to ground), I want to change the value of UUID or Major/Minor number
If not, the device will continue to advertise the previous values
Hello,
I am working on a custom project with nRF52832 using SDK14.2 and s132_nrf52_5.1.0.
Now I am trying to configure and use RTC2, and face the problem that ble_stack_init...
Hello everyone,
after hours of python module installation, I was able to run the PPK with PCA10056. I have cut the SB40 and used an external pwoer source with 2,5 V. I have...
Hi I have two problemes, I do not know where to start, so if someone has an example, I would like to see it. The first thing is if someone has an example about using pwm to...
When registering a base UUID with the SoftDevice via "sd_ble_uuid_vs_add", a uint8_t is returned which (per the ble_app_pwr_profiling example) is intended to be the "type...
SDK 14.2
I try to use the watchdog using this code
static void nrf_wdt_event_handler(void) { NRF_LOG_INFO(">>> nrf_wdt_event_handler") }
int main(void) {
...
nrf_drv_wdt_config_t...
Hello , I am working on the development kit nrf52, i want to know how i canget the value of the RTC overflw and then how i can reset the RTC to zero.
thank you in advance...
We are developing a React Native mobile application for iOS and Android, making use of the react-native-ble-plx library to interface with the BLE UART service from the examples...
I'm running various example programs, and would like to find documentation for the functions I see them calling, for example nrf_drv_saadc_init...
Where can I find documentation...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
Hi, I'm having an I2C read lock-up issue similar to those described here , here , and here .
I'm using SES, SDK14.1, and an nRF52382. The only other component on the I2C...
Hi,
I have a custom board with nRF52832 SOC and temperature sensor in it.Interface Between the nRF52832 and Temperature sensor is I2C.i have to see the data through the...
Hello
We are currently making STN1170 based OBD II scanners with the nRF52810 for communications. The product is stable and available for commercial deployment, however...
