Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am experiencing an issue with my nRF915DK board. When I connect the board to my PC via USB, the debugger LED blinks continuously.
I have the same issue with a nrf52840DK...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello!
I don't know if there is a way to configure a nrf52832-QFAA's clock source on my custom board software-wise.
Just a disclaimer but please correct me if I'm wrong...
Hello,
Before I start to over-develop I need to ensure that there isn't a better solution based on the nPM1300 behavior or capabilities.
Context
I'm using an nPM1300...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
My application is based on the ncs nrf5340_audio application, but my application and hardware target are both out-of-tree and I am using ncs v2.9.0.
I am able to connect...
I've updated the nrfconnect sdk to the version 3.0.1. and the zap tool version is 2025.5.22. The sdk supports matter 1.4, but the new device type of mounted dimmable load...
Hi,
1.Please provide the documentation, examples and tools for testing the RF performance of nRF7000 during the mass production of nRF9151 + nRF7000. 2. If not, please provide...
Hi,
I'm working on a custom board based on nRF52840 and a 2.9" ePaper display (SSD1680) connected via SPI using the mipi-dbi-spi interface. I'm using nRF Connect SDK v3...
Hello,
Not sure where to post this or who to notify, but after the most recent Nordic DevZone site maintenance, I keep getting multiple emails from the DevZone with the...
Hi,
I assume this would apply to most new boards - but I am finding that the build time since upgrading to newer hardware has increased significantly. Perhaps due to sysbuild...
I have a application where I need to time acurately the time between two enternal pin signals. I have this working using the
k_timer which & read & restart within the...
HI， In the Zephyr config, these【NET_IPV6_NBR_CACHE & NET_IPV6_ND】 are recommended to be enabled by default. Why does the Bulb project turn these off, and what impact will...
Hi I am currently trying to modify the Zephyr BLE Controller stack and getting exceptions. It seems the "J-Trace PRO Cortex-M" can help me with knowing how I get there. Buying...
Hi.
I'm evaluating the LE Audio Auracast using some nRF5340 Audio Development Kits.
I programmed a board as the source and a board as a target and I successfully played...
