We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I picked the above Image from this Link Nordic Mesh_Product_Bluetooth Mesh
I would like to know ADV bearer and GATT GAP features available in Mesh SDK 10
I just built nRF5 SDK for mesh v2.0.0 -> ‘light_switch_server_nrf52832_xxAA_s132_6.0.0’, but there is a compile error, "boards.h: No such file or directory".
My dev environment...
Helo, Im trying to sending data from sensor between two nrf52832, SDK 15.0.0 SoftDevice S140 on both. Im using uart central and peripheral examples on transmiter and receiver...
Hello,
Like in the description, I dont get this to work. Im trying to get The nRF24L01+ connected to a PIC16LF18345. I did Some Pictures of the SPI logic and Here is a Part...
I have the nRF52840 PDK and tried to download the firmware as per step 7 to paste it to the JLINK folder to make LED1 blink so i can test NFC but cannot get led 1 to blin...
I was wondering if adding a capacitor in parallel with the coin cell battery would help with the battery life by smoothing out the peaks. The scenario shown in the chart is...
Hello All,
I have successfully built the secure_bootloader app. I have the bootloader working with the button. I can upload application files using DFU. I tried the buttonless...
Hello
I'm currently running ble_app_uart__saadc_timer_driven__scan_mode and would like to modify it for faster sampling rate. However, NRF_ERROR_RESOURCE presents an obstacle...
Very new still learning.
I am using Keil and trying to setup the tools>customize tools menu.
Following the tutorial I am able to create the eraseall macro. No problem...
Hello~!
I am working on modifucation code of ble_app_uart example.
nRF51822
(SDK12.3.0_d7731ad)
Softdevice 130 (v2.0)
I know the original UUIDs are provided from...
Hi, I am working with the example Blinky_freertos present on the SDK_13.0.0_04a0bfd.
I have built the example w/o issues in compilation but I have the following problems...
Hi i get this error when compiling. (version 0.9.7)
I'm using arduino DUE and BLE Shield (redbearlab).
I get the error: EEPROM.h: No such file or directory in bootloader_setup...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
