I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello, I am practising and studying the beacon example on nrf52840. While reading the main code, I try to delete the log_init part, however the kit doesn't advertise. I am...
Hello, I hope to realise a scenario that, my kit(nrf52840) advertises certain information, all the mobiles nearby (with BLE) could receive the information. I think the non_connectable...
Hi,
I'm looking for mBed OS 5 examples I can run on the nRF52-DK. At the mBed GitHub, I only found a Blinky and a BLE sample. I'm wondering if you are familiar with more...
I can see that there is one example for UART and it uses application uart module (APP_UART_FIFO_INIT ...). I used this module for printing strings on terminal window, but...
Hello,
I have been working with a nrf52DK PCA10040 V1.2.1 on SDK 14 without a softdevice and I have encountered a problem with a TWI sensor.
I have a TE MEAS MS5611...
Hello,
my usecase is the following: I'd like to use SoftDevice for BLE Advertising / Scanning - every now and then I'd like to "pause" BLE for a few miliseconds and send...
I download the demo project \nRF51_SDK_8.0.0_5fc2c3a\examples\peripheral\uart\uart.uvmpw to my nRF51-DK board, but uart didn't work,all 4 LEDs are on. Is there any mistake...
Finally, I managed to compile ble_beacon in segger.
However, here's what I can not understand.
Using either Segger -> Target -> Download File
or RKNRFGO I managed to...
I got beacon which use nRF51822.
I need to get radiated pattern diagram as attached picture.
this is to get KC certificate.
How can I get information? beacon maker...
Hello,
I'm using a module based on the nRF52810, the Fanstel BT832A. I'm running the basic "ble_app_beacon" firmware from the "nRF5_SDK_14.2.0_17b948a" SDK with a few changes...
I spent a few hours trying to change the base UUID and handles of the attributes of the Blinky peripheral app, just the one service and the button and LED characteristics...
I have couple of nRF51422 boards, nRF5-SDK-for-Mesh (v. 1.0.0) and good will to demonstrate some simple multihop mesh.
And I want to write some data to the flash, but operating...
Dear Nordic,
I are using nrf52832 to develop a product that needs FCC certificate,
We use a PA and can increase the output power up to 20 dBm and it
seems that is lower...
Hi guys, I’m doing several tests with my new RedBear BLE Nano v2 board based on nRF52832 using the RedBear library, but I found a problem with reading Notify Characteristics...
