When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am using nrf52832_xxaa and I'm porting my device from SDK11 to 14.
#define APP_SOC_OBSERVER_PRIO 1 /// Applications' SoC observer priority. #define APP_BLE_OBSERVER_PRIO...
Hello guys,
I have got some evaluation project based on Mesh.
I have got Mesh SDK (nrf52832 DK Based) and Thingy52 Mesh examples working. Even we created sample Android...
How is the output power effected by temperature on the nRF52832 chip? Is there any data or documentation specifying the change in output power vs low and high temps?
Hi,
I use the bootloader example given into the library to update my application (or bootloader and/or softdevice+bootloader) via DFU but I don't find in this code how to...
Hello,
I have questions on the Provisioner of a network. Reading through the documentation on Mesh Provisioning, I have come to understand that some amount of data has...
I've tried this but it does not work: static void adv_slots_init(void)
{
uint8_t default_frame_data[] = {0x03,0x03,0xAA, 0xFE,0x13,0x16,0xAA, 0xFE,0x10, 0xF8,0x03,'g','o...
on the nrf52832 I am configuring pin 10 as an input. There is either 0 or 3.1V on the pin depending on whether a charger is connected to the board.
When I read the state...
Just stumbled upon this:
#define TIMER_PRESCALER_PRESCALER_Msk (0xFUL << TIMER_PRESCALER_PRESCALER_Pos) /*!< Bit mask of PRESCALER field. */
Should be
#define TIMER_PRESCALER_PRESCALER_Msk...
I am working on project where I am storing and reading data from an SD card. During the initialization, I would like to print the full contents of the root directory - "/...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I'm using nRF52840-PDK. I created a custom ble service following this tutorial ( github.com/.../custom_ble_service_example) and sent my sensor data over bluetooth. Now I'm...
Hi ,
I am trying to disconnect a connected central (phone) by calling sd_ble_gap_disconnect from my nrf52 configured in multiperipheral mode. . The disconnect call returns...
I am trying to time a capacitor discharge through different resistance sensors for greater resolution than an ADC. I did this using the GPIO functions initially but the SD...
