Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi there,
Is possible use nrfjprog to write in flash the data time using windows batch commands after programmed the device?
actually, I want to use the nRF52 as a RTC...
I have a question about the nRF52840 QIAA Reference Layout v1.0 which can be found in the infocenter /nRF52 Series/Reference Layout. I saw that it has keepout areas on mid...
I'm trying to implement an application for the nRF52832 that will provide an OTA update to another external nRF52. The code for the device accepting the update has already...
HI, i want to know, how can i use the feature of LE Data Packet Length Extension which in core v4.2.
i want to connect the PDK with the my phone, What should we change?
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
Hello I was trying to run the Power Profiler Module with nRF Connect but I geting the following error:
ps: The python solution is already working for me.
What is the RTC run current on the nRF528120? It is not listed in the datasheet.
In addition, what is the run currents for the clocks on the 810? There is no information...
I need to send data from PC (windows 10) to nrf52832 using UART (hardware) in order to retransmit this data through mesh network with light switch example.
Do i need to...
Because I'm using PTR9618 module of nRF52832, it don't have XTAL 32.768Khz (X2).
When Makefile have NRF52_WITHOUT_SOFTDEVICE=1, hello-world, blink-hello work fine. But when...
Hi,
I'm looking to generate a clock signal on a gpio with an exact frequency. I tried this by setting the pwm base clock and adjusting the top value but got no luck.
Is...
Hi Nordic,
I find somethig wrong while using GPIOTE.
I.
First I call nrf_drv_gpiote_out_init(MY_PIN, &my_config), it works fine. However, I call nrf_drv_gpiote_out_uninit...
dear sir
i had use the ble_ant_app_hrm demo to test ant+ble,but i could not find the softdevice in the folder,so i can't connect it to my mobile phone,the link address is...
Hi, I'm using Central multilink example to connect with our Custom Peripheral sensors. I'm using board PCA10040, nRF52832, SDK_14.2.0, s132. Sensors have a custom service...
