here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi dear friends from Nordic Semi,
I´m in great trouble trying to make these nRF24L01+ to work, one unit as a transmiter, and one unit as a receiver, it can be to send 3 bytes...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
Hello All,
We need to design a Remote Control based on NRF24LE1 working with mercury cell.
So they key factor is hardware & software optimisation for the lowest possible...
Is anyone aware of any of these on the market yet? I know of one, from Insight SIP, but am keen to hear about any others.
(This would save space on the PCB, simplify our...
Using twi_sw_master have discovered that the nrf51422 E00 draws 1.3mA in off mode.
When the twi device is removed from the bus, the nrf51422 draws under 5uA in off mode...
I want to merge soft device, application and boot loader in order to improve efficiency for factory. I searched relative topics in this forum and found something useful. At...
We have been unable to establish a link between a Garmin HR monitor over the air, we have established USB comms to a cell phone device. We took the transmission line directly...
i find one related question:
devzone.nordicsemi.com/.../
and this is refers to nrf8001,
so, i wonder if nRF51 could share both crystal with other MCU?
please help to...
Hello,
I am trying to test ble_app_uart example code and replicate similar behaviour.
I have disabled hwfc. But without hwfc, UART0_IRQHandler is not getting called...
Hi
I need to implement I2C slave side (up to 100kBit/s) on a nRF51822 chip. As far as i see the inegrated TWI peripherial only supportes the master side. Any ideas how...
I just received an nRF51822 eval/development board that has a sticker on it that says "PCA10004". I also just downloaded the latest SDK (nrf51_sdk_V6_1_0).
As far as I...
I received my nRF51822 development kit today and the PCA10000 dongle doesn't appear to be working. I installed all the drivers/software as per the user guide and when I plug...
Hi,
I'm using s110 v7.0.0 and sdk v6.1.0.
Which situations can produce disconnection error 0x3E ?
( BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED )
how to avoid this error ...
Hi All,
Are there any updated examples for nrf51822 for writing long charecteristics.
My Application has to receive more than 20 bytes at a time and send over uart.
...
