I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
We are looking to add some device info into the advertising package, or scan response package depending on space. When looking for a way to do this in a standardised way I...
Hi.
I'use nrf51822 beacon kit and android nrf beacon app.
I'm modify nrf51822 beacon example source code,
I hope
1.I eliminated the button
2.After I turn on the...
I'm new to nRF51822 Evaluation Kit. I was able to build the hex from "ble_app_hrs" example with GCC and Eclipse. However, it won't allow me to flash it by drag and drop to...
Hello, I'm an developer using nrf51822.
I have the same problem with this.
devzone.nordicsemi.com/.../
But this problem has no more discussion...
Here is my problem...
First I load soft device through nRFgo.
Then I run debug with eclipse.
I then step through code in main.c ...
(I'm using QFAAG0 chip)
Stepping worked fine when I used...
Hi,
I use a system with BLE softcore running - and can generate highly precise pulses with the gpio pins using Timer1+2 with interrupt service routines. Jitter might be...
Hi,
I want to use nRF51822 to do some development in the eclipse.I follow the document(nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1) step by step,when...
Using PCA10001 Evaluation kit, SDK v6.1.0_b2ec2e6 and SD s110_nrf51822_7.0.0
IOS app nrf Toolbox HRM on iPhone. Everything is working fine, get the advertisement, connect...
Hi all,
Short version: I want to make 200 devices using nrf51822 (and S130 v0.5.0-1alpha), all advertising/scanning at the same time, and process RSSI readings for proximity...
I am trying to find out what is the difference between nRF51822-mKIT and nRF51822 EK . Visually both of the boards look identical and the only noticeable difference is an...
I just tried setting up on Windows8.1 but can't see the "nRFgo Studio".
I got as far as step 4 on page 9 of "nRF51822 Development Kit User Guide v1.4",
but it doesn't...
I have a RedBear Blend and I want to talk to it from iOS.
I'm currently using the default setup provided with the Blend and RedBear's library over the top of the Nordic...
Hi, after a deep study of Datasheet I was finally able to have two 24L01+ talk to each other with a PIC18 program.
Now I need to make a step further using ACK Payload since...
Hello,
I am trying to verify hid_keyboard_demo app running on nRF51822 with android running device.
I have tested it with my phone running android kitkat and windows...
