Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
I am using softdevice 6.0.0 and ble_app_hrs example in keil on a custom nRF51822 board. Compilation goes fine but when I try to debug I notice that the firmware seems...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi
I am using S110 v6.0.0
I have written an app that has a single service and I then register the same characteristics until it fails. The properties is 0xA (read/write...
Hi,
The nRFgo Studio v1.16.1 will up side down the contents of old profile XML that created by v1.16.0 or v1.15.x.
And use the new generated services.c and services...
Hi,
So I'm using a BT 4.0 dongle (Laird BT820) to set up a LE notification loop with the nrf8001 (RedBearLab shield on Arduino) using gatttool on Ubuntu 12.04. This works...
I've used the nRF8001 on several projects with good success, so I'm generally familiar with the chip's operation. But I'm seeing an issue on a new (custom) board that I'm...
We are currently researching which BLE chip vendor to use so this question is directed at Nordic personnel familiar with the S110 stack's capabilities.
In a situation where...
I would like to use the nRF51822 evaluation kit as an observer to detect beacons and take action based up the RSSI value. I can't seem to find any source code for S120 or...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
Repro, using the Nordic hid-profile + iOS 7.1.1:
Pair the nrf51822 based hid device via the iOS bluetooth menu.
Turn off nrf-device.
Boot up the nrf-device...
I want use pstorage write and erase flash,as shown below:
//pstorage_init(); // device_manager_init have been called,so there's no need to call
err_code = pstorage_register...
I currently have a design that has four characteristics (all strings) in a custom service. Each is less than 20 bytes and I send them out one at a time. i.e. one characteristic...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
