Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm trying to debug issues in my application related to FDS garbage collection.
My application periodically runs fds_gc() from startup. At this point, garbage collection...
Hi
I got a nrf52833 dk and followed "nrf52833_heart" SDK file readme file is success
next step I install segger studio and JLink_Linux_V662d_x86_64.
wend i open studio...
Hi Devzone:
I saw two functions to write the retention register for DFU, nrf_power_gpregret_set and sd_power_gpregret_set.
What's the diffrence between
nrf_power_gpregret_set...
I'm experimenting with multiprotocol support on a PCA10056 (nRF52840) and the S340 softdevice. I need to use BLE and ANT+ at the same time, sending data to either ANT+ or...
What type of cable is required for the debug out, P19?
The specs for the port only say the number of pins, but not the pitch https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk...
nrf52840 packet transmitting time measurement for TOA or TDOA
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
What I’m trying to...
Hello
Where is the the timeout for the Resolvable Private Address (RPA) defined?
only possible in the central?
can I change the timeout in the android nrfConnect...
Hi,
I am using nRF Connect (Desktop) v3.3.0 with a nRF51 dongle with the latest firmware to test my BLE device application.
My application contains 1 customized service...
Hi all,
My goal is to store large data which is approximately 300KB and send it using UART. To do it, I think I should the library of NVS on zephyr. I achieved to use it...
Hi,
I am trying to make a design for the m odule ISP4520 from ISP, which is basically a pcb with a nRF52832 and a lora radio.
However the processor on the RF52832 is not...
I need to share the LFCLK with an external device and I'm thinking on using an external oscillator like SiT1532AC-J5-DCC-32.768E
I'll set the LFCLKSRC registry as 111 (Apply...
I am setting up a build server that will take care of building our app for the nRF52 and creating the DFU files. For DFU package, I need nrfutil.
Everything is working fine...
The document infocenter.nordicsemi.com/.../nan_040.pdf shows the recommended sizes of the pads (0.275mm) and apertures for the stencil (0.3mm). To connect the inner rows of...
I have some nrf52382 nodes. I want to form two subnet in mesh.
if i using different provisioner to make subnet or something else ？
1. How to Create two subnets: Subnet...
Hi, I'm using metamotionR of Mbientlab that have nRF 52832 ( I attached the circuit of metamotionR )
but, I want to develop new firmware on this device. so, I started with...
