Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I'm struggling understanding how DFU works on nRF52840.
I know I can update the firmware via the Connector application, but I'm trying to use the nrfutil over command...
Hi all,
I am using Thread SDK3.1 and running successfull with MQTT-SN example (Border Router + 1 MQTT public + 1 MQTT subscribe)
Now, I want to change MQTT broker from...
Hi,
I am programming for an nRF52840 chip. I am using Keil uVision with the ARM compiler in version 5. My codebase is in C++, this is why I have the Misc control "--cpp...
Hi
I am currently using a nRF52833 DK. I am working with the direction finding feature of the nRF52833 DK. I have managed to send and receive CTE packets and I am getting...
The link given still points to the windows executable when selecting macOS or Linux on https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Connect-for-desktop...
I have CONFIG_GPIO_AS_PINRESET defined in my project (both bootloader DFU and main program), so pin 21 is setup as hardware reset.
I would like to disable this function...
Is it possible to use one of the development kits to simulate a cell phone so that I can test my device's bluetooth pairing, connecting, and communication?
I know I can...
hello, I'm working on the nrf52832 and sdk15.0.0 , I made my first custom perihperal with custom services, and now i want the device to be connected only to the first device...
I just got my developer Kit and follow the instructions in https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/GetStarted#infotabs -> GET STARTED
when...
1. Is there any document available from Nordic that describes the exact steps to measure power consumption in PSM mode with the Dev Kit? Also, is there a test firmware available...
Hello,
When in try to activate "Console 'get' function selection" in menuconfig, I get an error "ERROR: undefined not in named choices or syms".
Can someone help me please...
Hi all,
I am doing a project with nrf52840 tags. I would like to collect the RSS values and the time stamp with my Android phone. I can see in the nrfConnect application...
Is the data stored in internal flash for mesh encrypted?
Or is any of it encrypted?
I'm talking about the data explained in this link:
https://raw.githubusercontent...
Hi,
I have test setup consisting of 2 boards, one that sends a packet every 2 seconds with CTE, and another with a 2-antenna array that generates MagPhase samples and sends...
Hi,
I am using "http_upgrade_ota" project.
I have added UARTE2 , SPIM3 and WDT peripherals in the application.
To use this peripherals i had to make change in "spm...
