after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
Dear Nordic
my SOFT DFU fail when I init the WDT, but I have feeddog and disable the WDT, like below:
static bool app_shutdown_handler(nrf_pwr_mgmt_evt_t event) { switch...
When access_model_subscription_list_dealloc() is called the entry is memset to 0 and the ACCESS_INTERNAL_STATE_INVALIDATED flag is set.
The function access_model_subscription_list_alloc...
Hi all,
I have a nRF52 DK (PCA10040 V1.2.1), and I want to learn how to develop on macOS.
I read from this link , and I got following information.
But I cannot know...
Hi,
I use The Texas Instrument software "SmartRF Packet Sniffer Bluetooth Low Energy" to catch the communication between my peripheral build with nRF52832 and Zwift (software...
Hello
I am trying to configure your TWIS (not using the SDK) and have run into the problem that the TWI master cannot pull the SDA and SCL line low. So, the communication...
52832's PDM function. After initialization, call the nrf_pdm_enable function, and then call the nrfx_pdm_start function. NRFX_PDM_ENABLED is set to 1. But the clock pin always...
I am evaluating the NRF52810 (using the PCA10040 dev kit), and I am having a hard time getting down to the described power consumption of the chips. I am using the power profiler...
i have done ble_app_template writing values from nrf app connect, in that i have send only integer values from nrf app connect
now i want to write float values from nrf...
Hello,
I have enabled the watchdog timer in nrf52810 with below code
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Pause << WDT_CONFIG_SLEEP_Pos...
Hi,
I have some problem with experimental_lpn project from sdk_for_mesh. (Today I tried both sdk 3.2 and 4.0)
Code loads and starts ok on my PCA10040.
After first steps...
I use NRF52840 Evaluation Kit.
I want to use TIMER with nrf_drv_timer. However, I get an error and cannot use it. The error is the following part of "nrfx_timer.h".
...
