Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
I get an error fatal when running Heart rate collector example from SDK12 on PCA10040 development board.
The sensor use example from SDK15 on a nRF52840-DK.
Some...
Hi,
I want to use Segger Embedded Studio to write firmware for Thingy 52 but I don't know what programming hardware I need. Is there any documentation that supports Segger...
Hello,
Thank you for helping me to interface the Si7021 humidity and temperature sensor with Nordic nRF52 development kit board. I need to write the necessary code to finish...
Hi,
I am using nRF52832 for my development, I want to send 8 bit device ID as an advertising packet with company ID and Data.
Is thereany way to send the same or any example...
In earlier releases of the mfw for the nRF9160, we got 3 files with the image, one of them being firmware.update.image.hex. This is missing in the new updates. How do we update...
Hi, I have a PCA10000 nrf51 dongle, I use with wireshark and the nrf sniffer plugin. I followed all installation steps for the version 3 of the sniffer and the latest version...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send datas from sensor (accelerometer...
hi
i use sdk12.3 (51822), i see only ble_app_hids_keyboard and ble_app_hids_mouse.
I want use mouse +kb device. I use ble_app_hids_mouse add kb function . then my android...
Dear All,
For a reason that I can't understand so far, I must erase the nRF52840 to be able to use UART1, TX RX on pins 0 1 (connector P14) to communicate with an external...
Hi,
Do you know which of the two version of ADP5360 the Thingy 91 uses?
is it
ADP5360ACBZ-1-R7 or
ADP5360ACBZ-2-R7
Both versions are available now at Analog's...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
"nrfx_wdt_event_handler_t" can be set in "nrf_drv_wdt_init". After the "nrfx_wdt_event_handler_t" event occurs, the WDT is reset...
HI，
When I use NRF58240 to develop GPS positioning function, APP_UART_COMMUNICATION_ERROR appears, but when I do not connect the GPS module, there is no such error. What...
Is there any test firmware available (or reference code) for doing total radiated power measurements? I have the nRF9160 designed onto a PCB and we'd like to do some antenna...
