I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello, i have question: How nRF Connect SDK gets MAC addresses Steps: 1. I build android ble peripheral app and starting advertaising. When i did it, MAC address alwalse random...
Hi,
Greetings!
I am using below setup
nRF52832
Mesh SDK 4.0.0
SDK 16.0.0
Application Example: light_switch_client_nrf52832_xxAA_s132_7.0.1
Issue:
Using above...
Hello,
I am referring to this webpage https://github.com/bjornspockeli/custom_ble_service_example "Custom Service Tutorial", I followed all the steps mentioned on the webpage...
I started developing a beacon app and used BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED advertising type. I then changed the type to BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
pc-ble-driver compile on macOS
I am trying to compile pc-ble-driver on macOS 10.15.2 by following the very excellent instructions on the github page.
Fixing GCC issues...
Hello,
I have set the device advertising as follows:
Advertising name is getting broadcasted with a full name until it gets changed and to 4 letters device name. In...
We have our SCL line on P0.10 (NFC2) and SDA P0.23
When I try to start a I2C transaction nothing happens, and NRF_TWIM0->TXD.AMOUNT = 0. I have verified that SDA/SCL are...
Hi,
I tried to implement a unprovision method for provisioned devices such as light bulbs. By simply on off it several times. And saving state into flash.
Currently I...
Hi Nordic Team,
Please share logic to de-initialize the advertising functionality of peripheral devices after the peripheral device stops advertising without any memory...
Hi Nordic Team,
In my BLE project, first the central device starts scanning, then the peripheral device starts advertising, the peripheral device gets connected to central...
HI,
I got nrfutil + BLE DFU app update working using the ble_app_hrs for the test. I am using the nrf52DK + SES for development, and I have also an external nrf52832...
Hi
I'm using this simple_pwm code to drive my speaker, I use this as a buzzer but I want to change the frequency.
In this code ".base_clock = NRF_PWM_CLK_125kHz", the...
Hi, I am developing an IMU app communication with ESB. I would like to send to the board a command with ESB to put the nrf52832 board in BLE DFU mode.
I have look at the...
I am using the timeslot API, and I have noticed that if I read Timer0 as the first thing in my timeslot, it will be at 75 us. This delay is very consistent, so my timing between...
The following change was introduced in v4.0.0
Note that mesh_config_clear() was replaced with mesh_opt_clear() which is a rather big change of behavior that wasn't documented...
