Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello!
We are trying to get low average current consumption on the nRF9160 DK without success.
The floor current between modem active time is ~60uA, which is fine. But...
We've recently been testing the accuracy of the GPS on our devices. My basic method has been to trigger on GPS_TRIG_DATA_READY/GPS_CHAN_NMEA, and at each trigger fetch both...
I would like to advertise some sensor data (temperature, humidity, pressure, co2, voc and other) by BLE advertising packet without any connection. I know, I can put it data...
How much ram is my application + Zephyr + modem firmware using and how much is available in the nRF9160? I'm unable to find a memory map and anyway that wouldn't include dynamic...
Can we alter the eddystone tlm (telemetry) packet to send custom data . [This is not following the standard packet structure].
But I wanted to know how to alter the given...
I need a product that will allow me to connect a PC to a Bluetooth device through its Bluetooth connection. I will need to be able to send data bytes from my PC across the...
Hi everyone,
I am a beginner with Nordic SDK. I followed the " Getting Started Assistant" and then try to open asset_tracker project on step 4. During the opening I got...
Hello,
The fds.c fds_register() has suspicious usage of atomic variables.
It is first checked if there is space in the m_cb_table, then m_cb_table is modified and only...
Hi, I am trying to add timer information to the sending packet. We created some space(manuf_data) to store data. However, the problem is we do not know how to put actual-time...
Quick Summary: - Devices used: nRF52832 (Central), nRF52840 (Peripheral)
Example based on : BLE Scanner
Hi Team,
In my current application, based on a BLE Scanner Example...
Hi,
I'm using the latest SDK v16. I got the following error when call peer_manager_init()
<debug> nrf_ble_lesc: Initialized nrf_crypto. <debug> nrf_ble_lesc: Initialized...
Is there a recommended way to inspect the state of the heap? I haven't found anything obvious yet. I'd mainly like to know the amount free, the largest block, and perhaps...
Hi,
I start developing with ble_app_template and DK
I combine uart spi twi into it
It can connect to my phone(nRF Connect APP)and work fine on DK
However when i use...
We want use Nordic chips as the transfer medium for our data frames in mesh-like network.
So we don't need ATT,GATT,GAP,SDP,SMP and all high-level things.
As I can see...
