Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hi,
As the subject description, I just remove the part of hid function from main.c then make the personal source file.
Before I removed, the project could work as usual...
Dear Nordic
there are two question find in my software. it may be some matter with thest two question, so put here together.
1.
My software will be reset about several...
for the i2c_3 to work the following is needed to modify the SDK.
nrf/subsys/spm/Kconfig
```
config SPM_NRF_TWIM3_NS
bool "TWIM3 is Non-Secure"
default y
```
...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
I am trying to run a project on a Fastnel
BT840 module
I had the code running on The dev kit when we switched to the new hardware without a FL crystal I have been unable...
Hi,
I am working on writing data on flash and reading it back.
i am not able to read data which i am writing to it . i am posting my flash file please suggest where i...
I need to sendt several indications on one BLE_GATTS_EVT_WRITE event. If I just call sd_ble_gatts_hvx I get NRF_ERROR_BUSY Isn't it strange? API stats:
Only one indication...
Hello,
I'm a beginner and I have lots of questions. So I wanna communication with MCP4110 chip. But I can't. I configured SS, MISO and CLK pin in sdk_config.h. (SEGGER...
Hi, all,
I try to use NRF52832 as central and peripheral. When it is connected with peer as central, I try to send to peer a message with "sd_ble_gattc_write", but I can...
Hello,
I have enabled WDT for nrf52810,S112 with following configuration.
static void System_task_initWatchdog(void) {
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos...
I'm using the nRF52 DK with SDK 15.3.0. At this point I'm trying to get a UART loop back to work by tying the TX pin (P0.8) to the RX pin (P0.9). I have verified that the...
