Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi All,
I am using nRF51822 development kit without the motherboard .
I flashed the ble_app_uart (nrf51822/Board/pca10001/s110/experimental/ble_app_uart) and it was...
Hi,
I've received the nRF51822-Development-Kit, this morning and I can't download any software to the boards.
I've install keil uvision 4.71.2.0, nRFgo Studio and the...
Hi guys,
I plan to buy the development kit from Nordic but I had a couple of questions:
1)I know that in a previous question I posted I was told that I can use the development...
I bought the nRF511822 development Kit, not realising that it needs the nRFgo motherboard to supply power to it.So i have to make do with what I have. I am trying to power...
So this should be a trivially simple demo to run, but I'm obviously doing something wrong. When I build the sample application called "uart_example" in the PCA10000 folder...
Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Hello, I read an article on Nordic site about the Blend Micro:
*"The Blend and Blend Micro also natively support (with no extra wiring) all Nordic Semiconductor nRF8001...
Hi,
I have a few questions on how to receive data (from an iPhone app) as a a peripheral device on nrf8001 (with RedBearLab BLE shield).
Basically I am trying to receive...
Hi,
how do you use the jlink gdb server?
All i get is Target halted (PC = 0xFFFFFFFE),
gdb will obviously not show any helpful trace for that and continue doesn't work...
Dear Nordic guy,
I 'm developing LG product with nrf51822 chip.
I have some question.
Applcation SW timer use the rtc1 clock source.so,
When NRF_timer interrupt expired...
Hi, I'm attempting to use API 2.1.3 and am experiencing some weird issues with transmission intervals. When I use UpdateConnectionParameters to set a connection interval of...
Hi,
I want to upload a firmware using DFU mode.
If I use toolbox 1.8 app of android I can upload the new firm, but If I use toolbox on my iphone, when I push upload the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
