Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello Devzone,
I'm using a nRF52833DK right now, and it uses 73 pins for SOC. If I want to go to 40 pins, I'm having trouble figuring out which pins are for peripherals...
I am using NCS 2.7.0
i am running this build command from a terminal in VSC for the nrf/samples/bluetooth/Direction_finding_connectionless_tx sample
west build -p -b nrf5340dk...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
HI,
I’m using nRF Connect SDK (NCS) v2.8.0 with the blinky example.nrf54l15dk, In the project, I configured the following in Kconfig:
kconfig
CONFIG_FPU...
Hi Nordic team,
My nRF52832 DK (PCA10040) was working perfectly until recently. Suddenly, it stopped getting detected by my PC.
Current Issue:
The board does not...
Hello Nordic Team,
I’m using the nRF9151 DK board in Surat, Gujarat, India with a valid Onomondo SIM card . I’ve followed the setup instructions as per the Nordic Academy...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
Hello, I am trying to update the modem firmware to v1.3.7 using UART using the nRF modem bootloader API. For context, I am running nrf-sdk 2.9.1 and also using the SLM application...
Hi,
We’re working on a device using the nRF52832 and have DFU over BLE working correctly using internal flash. Updates work both via our custom app and the nRF Connect app...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
Hi
I noticed one ticket says that "the following combination offers low power consumtion and high througput when needed :Short Connection Interval + High Slave Latency ...
Hi, I'm a beginner and I'm trying to run an LED blinking program. However, I'm encountering a device-related error.
I've followed tutorials and installed all the necessary...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
