Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
Hi,
I'm planning to use the nrF51822 in the end product and the nRF51DK kit has nRF51422 and not the nRF51822. the user guide for the kit says that 51422 supports ANT protocol...
I am doing a bootloader to support updates via ESB. I am using MicroLib. I am not using SoftDevice.
My project mapping:
Bootloader 0x0000-0xBFF
Application Vector Table...
I use Keil uVision 4.74.0.22 to compile nRF51-ble-bcast-mesh-master with nrf51_sdk_v6_1_0_b2ec2e6 and get the rbc_mesh_BLE_Gateway.hex. However, I drag and drop the hex file...
The iOS app we have is identifying the device via the name broadcasted and the service UUID. On production devices, are the Service UUIDs on the same product, the same on...
Fisrt of all, I have searched all the questions but now still can't make bond work.
I've done below work:
1, modify main.c file to add device manger function
2, modify...
Hello,
I am using NUS service as a peripheral with read and write characteristics and tested on master control panel.
Now I am using S120 stack for central device and...
Hi,
I have a PCA10028 which has a 51422, and trying to run ble_app_uart_c example on it. But no success. I don't get any thing on COM and LEDs do not turn on at all. Does...
Good morning,
I am using nRF51 SDK v10.0.0 and I have to synchronize access to a hardware resource shared between two control flows. One flow is an interrupt handler invoked...
I just ported my SDK 9.0 app timer code to SDK 10.0 which requires the use of the new APP_TIMER_DEF() macro. The problem is that is generates warnings in Keil (v5.17) that...
I am using nRF51822. I want to know that how to perform file read, delete and write operations. Is there any API available for this. If file operations are not supported by...
We are trying to integrate an accelerator driver with the code written in c++ with example code from twi sensor from the SDK 0.10 for the nRF51, which is written in c. Will...
Hi,
I am struck with the problem of GAT ERROR when I upload my application zip file through Nordic nRD ToolBox in Android.
These are my steps:
I load the S310...
I recently migrate to SDK 10 from SDK 9 and printf is behaving weird with baud rate of 92100 (460800 and below works fine). Some of the characters were printed out of order...
Hi,
I am trying to implement some custom services in PCA10028 version 1.1.0 with Android, I am following same code which is in github ( github.com/NordicSemiconductor) it...
