Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,I update my MDK from 4.7 to 5.0,my old project can open ,but can't find the device list.I want to use 5.0 and 4.7 at the same time,and I have installed the SDK6.0 when...
Hi, when I compile my project the linker gives me the following error:
._build\nrf51422_xxac_s130.axf: Error: L6200E: Symbol GPIOTE_IRQHandler multiply defined (by app_gpiote_fast_detect...
I am working with nRF52832 and SD 132 and SDK 11 (nRF5_SDK_11.0.0-2.alpha_bc3f6a0).
One of my BLE services has a characteristic with an attribute larger than 22 bytes. It...
i was working with a nrf51822 module.after about 50 that i programmed the chip with my jlink programmer (some time i program it with stlink V2) it be damaged and not worked...
I am designing a BLE device. Want to make the PCB as small as possible. to download the code/debug etc I need the a connecter on the board which can connect to the nrf52 preview...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
Hello,
Two issues want to ask, after tried the BLE_NUS example code.
From other posts, still does not exist clear solution (example, pictures) ?
Sure has an application...
Hello,
I am working with the uart module. While configuring the uart I encounter 2 issues.
First when in the uart_init function the pin for uart output is configured...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I've never used Gnu's GCC before, but after 20 hours of trying and failing to install it on my macbook, I'm finding a shining hatred. I've downloaded their exhaustive list...
I migrated to nrf52 and countering some problems.
I am trying to sample 4 pins every 2ms with SAADC.
I started with Example here .
I simply changed
uint32_t ticks...
I've got a gyro I want to read some data from, but I don't know the values and can't verify if they got read correctly. When does nrf_drv_spi_transfer start to read?
i...
