I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Aim: I want broadcast ibeacon info in one broadcast packet, and broadcast ibeacon name at the next broadcast packet.
The broadcast packet data length is 30 bytes.
Q...
I am looking for some guidance as to the memory regions to reserve for the Bootloader hex if I pull it in via Segger Embedded Studio. I have the memory allocations for the...
I have a working application with TIMER1 setup to fire handler every 10us. I would like to add a 560us periodic event to enable/disable a PWM, so I add a little more code...
Hi,
Using the NRF52 DK PCA10040, I have built and loaded the KEIL temperature example project (C:\nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\temperature\pca10036\arm5_no_packs...
hello ,
i want to know if there an example available that has both peripheral + Broadcaster role running at the same time , Broadcaster advertise the service in the peripheral...
Hi all Nordic developers,
I am currently working on an application using a sensor (the temperature sensor) on a Smart beacon kit, which must connect and send data to a...
Hi all,
What's the difference between the Beacon Transmitter Sample Application example given in nRF51 SDK and the beacon firmware provided in the beacon kit? Are there...
Hello,
I have a nRF 52 preview board (PCA10036) and would like to use ETM trace to enable the "execution profiling" in Keil v5.
After I enable the trace and ETM trace...
Hi,
I am facing hardfault when i try to enable low power in a ble application. i want to enable trace on my PCA10040 board to find out the cause of this hardfault. can...
Hi,
We are using our own custom nRF52832 based board, with revision B silicon however we are having trouble getting trace functionality to work.
Our code uses the Nordic...
Hi,
I am going to design a new product around nRF51422 and I am planning to buy the nRF51 DK but I am really confused about the sw I need for development and additional...
I found this recent Q&A very helpful on the topic of reading voltage on analog hardware pins via the ADC: devzone.nordicsemi.com/.../
In that Q&A, a helpful Nordic person...
I want to use the MultiActivity Example with the nRF52 with GCC and Eclipse.
In the documentation I ve read that S130 and S132 are supported, but in the directory of the...
When I using the UART port, if I float the port after init the UART it will restart the code, is it need a external pull-up resistor? How about the value?
