Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Do conditional breakpoints work in Keil uVision5? I open the Breakpoints window and see:
If I set count to any value, I application still breaks on the first pass. When...
Hi
I have problem make the examples in the SDK 11. I get at "No rule to make target"
C:\konskimo\NYII\Spec\nRF52832\nRF5_SDK_11.0.0_89a8197\examples\peripheral\blink...
Hi,
when using timeslots I cannot turn off the external crystal that causes an higher consumption.
I already read this post and tried to turn off the timer0 (using STOP...
Dear Sir,
I merget (Software Device) + (DFU bootloader) + (Application firmware) into PE280_WS.hex
And use the script <<nrfjprog.exe --program PE280_WS.hex>>
it reported...
I'm having trouble building the ble_app_uart example in: SDK11/examples/ble_peripheral
My build environment is:
Ubuntu 15.04
SDK 11.0
GCC
S130
PCA10000
nRF51822_xxaa...
Hi,
I have a pretty hard time to get I2C/TWI running on my 52832 Dev-board (pca 10036).
My problem is, that i do not get any physical I2C signal out of the board's pins...
Hello, this might be a silly question, but i've seen various Nordic examples and i don't know whats the difference?
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS...
nRF52 series compatibility matrix says that you can get the IC revision using nrf_ic_info_get but it is only implemented for nRF51. Does the following patch add support? ...
I am attempting to follow the BLE UART tutorial and everything seems to be going well until I fire up termite and try it out. My phone successfully recognized and connected...
hello,
Every example of nordic is done with only one main.c file , i want to have a
separtate new.c and new.h file and take all the code from main.c and put it to
the...
Hello,
I am using SDK version 9 with softdevice s130 operating as both a central and peripheral. I provide a custom peripheral BLE service, and when it receives some information...
Hello,
I tried to use the example of SPI slave with the sdk 10.0. But I have an issue: the character "Ignored Transaction" is send on MISO pin.
I would like to now why...
Hi, I'm somewhat confused about using GCC, since I don't want to use Keil.
I'm using nRF51 DK.
I see makefiles in the example subdirs of SDK, but I would expect at least...
Hi all,
I am developing a mesh network and i am using pca10001 EK V2.2.0 for nrf51822. Some one suggested this link: github.com/.../sdk-8-support
I did what they suggested...
hi
in my nrf51422 v2 there r one phone that cant detect my nrf and i think its because of the phone because other phone can detect my nrf
now what parameter is important...
