hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Referring to the PCA10001 schematic, there is a solder bridge SB1, which connects AVDD with VCC_nRF.
Can you please explain in which cases is it needed?
Thank you
...
Hi all,
I test the DFU as follow:
erase chip, program "s110_nrf51822_5.2.1_softdevice.hex"
program "bootloader" by using nrfjprog.exe
"DfuTarg" can be found...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I'm trying to build the bootloader for gcc/Eclipse.
I used the manual setup approach described here.
However, I can not fit in the allocated space, because...
SDK version: 5.1.0
S110 version: 6.0.0
chip: nRF51822
I am experimenting a generic Data transfer hid device, the report map is as follows:
0x05, 0x0C, // Usage...
Hello Nordic team,
I am working on a BLE RedBearLab shield (nrf8001) mounted on an Arduino board.
Consider that a connection is correctly made from a Master app to my...
I've been running various code on a 51822 that has used PPI, timers, events, GPIO pin config and so on. Supposing I've lost track of what state the retained registers on the...
Hi,
I am new to ANT programming, and was following the userguide's steps to set up my nRF51422 evaluation kit (pca10003 board). I can compile and upload the blinky example...
Hello Guys,
I am having a hard time figuring how to add the nRF51xxx algorithm into Keil. According to nRF81522 Evaluation Kit user guide this should have been installed...
Hi all,
I use the SDK mouse demo and bind with a surface successfully.
But when it connected, I set the mouse re-binding again by pressing the bind button and power on...
When I first switch on the circutry that initialises the nrf8001 and sets it up for communication and then connect the android app with it ,the connection is done successfully...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hello,
I have some questions regarding S110:
Is it possible for the S110 softdevice to scan for broadcasts?
Is it possible to create a connectable broadcast...
