I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
Dear sir,
I am using your NRF24L01+ chipset with STM32F407ZET6 controller for 2.4GHZ RFID communication. can u please share the STACK for this controller.
I have a few questions (using nRF51 DK and/or external nRF51822)
I use an analog pin to measure the voltage of a capacitor of an analog circuit. From time to time...
Hello,
I would like to implement HID over GATT profile (BLE) in the Beaglebone Black (BBB). The BBB will be used to interface with a laptop/computer running Windows 10...
Sorry for this long message. I am new and quite lost.
I just purchased a nRF51 DK and installed nRFGo Studio, Keil MDK and NRF51 SDK. With nRFGo, I programmed the Segger...
Hi,
I'm trying to link the static esb library (esb_gcc.a) with the mbed toolchain. Everthing seems fine until the last stage of the linking phase where my actual functions...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
I have inserted the USB dongle nRF24LU1p in to PC. In nRFgo studio, it is detected as nRF24LU1+ Bootloader. If I click on the bootloader, It shows a window from where, it...
Hi,
I've got the following error when trying to update the softdevice and bootloader on my iPad:
Error on StartDFU Message:Data Size Exceeds
I've carried out the...
Hello!
Do I need any extra passives, connecting SD card to SPIM of nRF51?
It works fine with MOSI, MISO, SCK, SEL, VCC and GND directly connected, just want to be sure it...
