Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
My project name is Remote Operated Vehicle. Basically i am using a PS2 controller as the joystick to control the car. So, my aim is to build wireless interface between...
In this function in nrf_gpio.h, why is there a GPIO_PIN_CNF_INPUT_Connect value there?
Shouldn't that be GPIO_PIN_CNF_INPUT_Disconnect, or does it not really matter?
...
I need to pass a bit, to 500 recipients in a closed room.
My doubt is, 500 receptors works simultaneously without interference?
Ref. to buy:
www.ebay.com/.../251458486443...
I've seen various threads here with sample code attached that show how to set up a timer to measure a battery voltage periodically. They also seem to use an external crystal...
Dear Nordic Guy,I'm developing with nrf51822.
my costom code based on the hrs profile.and I modify the advertising timeout value to 30sec
and finally, I see the a few uA...
Hi,
I bought the nrf51822 chip itself, and created my own board. Now, can I still download the nRF51 SDK as per nAN-29?
I am stucked with the download page asking for...
Guys
I came over from the Arduino forums, I am searching for a new RF chip to use for a project i am working on but dont know which chip to pick. My application requires...
I want use uart to debug my ble program ,
In the devzone I found this and this to meet my need , but when I conditional compilation UART code into hex, I can not find my...
Hi All,
I am trying to use the HRM_RX sample code with my Linux PC side application. but i am not able to receive any UART RXD interrupt on nRf51422. I checked PC is sending...
We are developing a BTLE perihperal product using nRF51822 chip. But we would like our product can be up-gradable. So we will need a Bootloader (by UART or other interface...
while creating a Makefile for DFU, for BLE DualBank only, I'm getting some odd errors:
../bootloader_util_arm.c:19:1: error: 'at' attribute directive ignored [-Werror=attributes...
SDK v5.1 /v4.4.2
Keil 4.73/Keil 5.1
delay function seems doesn't work well in new version of keil. But I need it to bebug and flash nRF51822 with new keil.Need your help...
I would like to use an nRF8002 in a proximity detection application.
I would like to be able to send a request/command to the device to start a continuous or rapid transmit...
