Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi
I purchased the full NRF8002 kit I am searching for the source code for the nRF Toolbox app but I am not able to download source code. Is the source code available for...
Hi,
I need something that can be the Master and talk to the Evaluation Kit Board to try to send a large amount of data. Do the Master Control Panel, or the mobile app nRF...
Hi,
I am using the nRF6310 + PCA10005 +nRFgo Studio as the lower tester, the supplied python scripts as the upper tester, and my own custom board as the DUT.
I've looked...
Hello, I am working with nrf51822 on my pcb design by myself, I read temperature from chip, the result is about 90deg, (I have div by 4 for 0.25 deg) it is impossible for...
Is there a way I can tell which version of the chip I'll get from a distributor? It's not clear to me that I can tell, from, eg the Mouser product page which rev it is. Is...
Hi,
I am working on proximity android application, i implemented immediate alert service, which is working fine. Now i need to set the alert level on the tag for linkloss...
Hi
I am working with alert notification example. I just wanted to know how you have tested the alert notification client example implementation. Is it just by using the...
Section 28.9.9 of the nrf51 reference manual shows the Config register has 3 defined bits, BBA. A is for Hardware Flow Control and is one bit, 0 or 1, which makes sense. ...
Hi,
I'm trying to add more user services to LBS demo. I generated 128b UUIDs for my services. Then I should add them to list returned by scan response in function advertising_init...
Hello!
Sorry for a new guy's description.
We had a device running in normal firmware application mode, and the Bootloader was programed. It's our goal to accomplish DFU...
Hello
I am using the nRF8002 kit. I would like to inform the host (Android app) when there is a long button press on the input pin.
Is this possible and if so which BLE...
Hi folks,
I was wondering if someone has a reference implementation of a bootloader that uses exclusively ANT technology to make DFUs, being it ANT-FS or any other alternative...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
This is something for the legal department.
You had some questions here about the RFduino before. This question is about legal obligations Nordic supposedly imposed on...
Is it possible to use an nRF8001 without a separate microcontroller to advertise non-connectable advertising packets specifically containing battery level information only...
