I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Good day, I am using a USB to UART IC and it isn't working just because the nRF51822 Tx signal is inverted from this IC. There are some way to invert the UART signals?
I am building a new PCB board for a prototype. It will be used for proximity. It will blink on low battery. It also has a piezo speaker attached to a pin as well. My question...
Hi all. I'm now developing a triangulation solution for indoor robots as a project at my school. I have 4 radios, that I want to communicate with.
One master node send a...
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Attempting to program a softdevice hex file using Keil uVision and an ST-Link V2, I get:
No Algorithm found for: 10001000H - 10001013H
This is in the UICR (User Information...
Hello,
I am thinking about going to eindhoven the 20th of may for the nordic tech tour presentation.
My main interrest is the new v7.0 S110 softdevice which is to be released...
I have used the NRF51822 evaluation kit for a while now to design a product and it performed perfectly up until a few days ago: the onboard segger now fails to connect to...
hi,
i am using a light sensor which is SMBUS serial interface, i tried to interface twi of nrf51822 with the sensor, but i am not able to get acknowledgement from the sensor...
HI,
I'm using sd_app_evt_wait() for getting back to sleep mode between advertisings. I noticed that when I change the voltage in a small interval mode (40 ms between advs...
Hi, If i am running 2Mb radio channels, how many can i have operating in the 2.4Ghz space concurrently?
ALso, what mechanisms can be employed to detect and move frequency...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
Hi,
I'm using Nordic 8001 with Arduino.
I successfully connected to ANCS. The problem is that i need another iOS App that scans for services on my bluetooth device and...
Hi!
My problem is that my code works on the devkit PCA10004(PCB antenna) but not on my own custom board.
The devboard can be connected to and all characteristics can be...
Hello,
i would like to make device which will be dynamically change connection with centrals. It should be connected to the nereast device (with the most power). So I will...
Hi,
I am currently using this example code (pasted below). It is sending the character 'a' every 4 seconds. I can't figure out which part of the code defines the character...
