How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi,
I have programmed the radio_test_example to target having nrf51822 qfacaa chip. I have changed the UART pins as per the custom board.
It's working fine but showing...
Hi,
How can i wake up(interrupt) the nrf51822 device from "air" (from my iPhone application)?
For example after i paired iphone with nrf51822 i want to put the nrf to sleep...
I am using SDK 7.1 and I am attempting to use the Makefile.common found in sdk_7.1->components->toolchain->gcc->Makefile.common. However, the Makefile.common appears to contain...
I'm trying to send multiple 20byte notifications per interval through the NUS usart service to iOS 7.0, 30ms conn. interval in the UART demo app. It seems I cannot tx more...
Hello,
I'm working on a project with SoftDevice s120. I played with the project ble_app_multilink_central. The maximum number of characteristics per service supported by...
Our application includes a 32.768 kHz crystal oscillator with a nominal +/- 20 PPM accuracy. When I factor in aging over 10 years and worst case variation due to temperature...
Hi !
In questions question1 & question2 Petter Myhre gave a complete answers about count of max characteristic per service in s120 and how to resolve this restriction....
Hi,
I am now developing the BLE with our company's own sensor, so we are not using the motherboard. There always a problem when we use it. I am using the PCA10004 board and...
SourceCode_SSDI_BTLE_BeaconReceiver.zip I am starting to use the Nordic chips, and have a PCA10004 board running. I have modified the experimental_ble_app_multiactivity_beacon...
Hi Nordic,
I am a hardware/firmware guy without App development skills and I also lack the time to acquire these skills. I enjoyed your UART App during my development,...
Hi all,
First of all, I'd like to express how pleased I am using this development kit. The easiest ever to start with, well documented and most importantly I can use the...
hii...
am using nrf tool box app in my iphone. i have tried to use dfu feature.i flashed softdevice and bootloader hex file to he evaluation board and in i phone app i...
In the "NRF51 Series Reference Manual" (v3.0) it states:
The LPCOMP shares registers and other resources with peripherals that have the same ID as the LPCOMP.
You must...
I have a timer that wakes up every 20ms to read twi.
Unfortunately it takes 4.4mA for the CPU to execute code from flash.
I would like to reduced the current consumption...
