Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi,
i am evaluating the use of the nRF51822-QFxx for our product and made good experience with the nRF51-DK. Now, i would like to layout the custom pcb and i am not sure...
Hi
The definition for nfc_t4t_ndef_rwpayload_set() is that it takes buffer_length parameter.
And the comments state "buffer_length Length of buffer (maximum writable NDEF...
Hello there,
I have developed a board with nRF52840 and a sensor. My hardware and tools setup is:
SDK: nRF5_SDK_for_Thread_v0.10.0_e1c3d11
Thread version:OPENTHREAD...
Hi, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it using eclipse. Here is the code:
Someting is not working and...
I am able to disable the reset function of P0.21 by erasing UICR register and undefining CONFIG_GPIO_AS_PINRESET .
Still i can't set P0.21 as output and set it to 1.
According to the User Guide,
After each byte has been sent over the TXD line, a TXDRDY event will be generated.
When all bytes in the TXD buffer, as specified in the TXD...
Hi everybody,
I need to preserve 3 pages of data in flash memory during DFU. I know there is the macro DFU_APP_DATA_RESERVED defined in dfu_types.h but, I was wondering...
We need to sample two digital inputs GPIOs at rate of 100khz-1mhz. How can we do that?
The QDEC is only good for up to 128us (~7khz) which is too slow for us.
Is there a...
I'm not able to get clear/un-corrupted data across the ttyACM on the nrf52840-PDK. I must be missing something, seems like this would have been solved a million times, but...
I recently experienced an issue with a race condition between peer manager and FDS in SDK 14.2 which was resolved under this case:
https://devzone.nordicsemi.com/f/nordic...
Hello,
I develop entirely on Linux and I am unable to find the --sd-req / --sd-id required for generating a dfu package zip using nrfutil . I am using developing for the...
I defined custom service (NRF51822,S110) to send sensor data. Code follows. Here I enabled notifications for new data. I can able to receive data, if I enabled notification...
Hi,
I have the following set up:
The remote: nrf51822 acts as central
The wheels: Each wheel has nrf51822 acting as peripheral.
The remote needs to first connect...
My application needs to be notified of large current draws due to the activity of the nRF8001. The active signal works fine for this purpose, but why is it available only...
