Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hey dear Devzone,
I am trying out some Thread and BLE dynamical examples on my nRF52840's but running into some problems using the " ble_thread_dyn_mtd_coap_cli " example...
Hello nordic dev community,
I am completely new to nordic products. I attended one of the conference and got more information regarding developer zone and info center....
Hi,
I am wondering why the ccm library uses the software aes encryption. Is there anything wrong with the hardware encryption so that it should not be used?
Marius
Hi there,
hope you are doing fine.
I am using SDK 14.1 with SoftDevice 132 as well as a state machine framework which needs a have a function called periodically to...
Hi. I'm using nRF52832, SDK13.0.0 as peripheral.
When I want to disconnect central, I'm using sd_ble_gap_disconnect function as below.
err_code = sd_ble_gap_disconnect...
When I try to build and run any example from the nRF5 SDK, it can compile successfully. But when loading to the eval kit, it can't find the 's140_nrf52840_5.0.0-2_alpha_softdevice...
Hello Everyone,
I am using nrf51822 256Kb Flash and 32KB RAM Raytac's BLE module with SDK11, S130 with over the air Bootloader (16Kb).
So the aim is that when a particular...
Hi all,
I encountered a problem , when I connect 1 board central to 2 board peripheral via NUS . It connected and discovery success . But at
static void db_disc_handler...
I was compiling a project(ble_app_uart and I am using PCA10028), it was not successful and KEIL5 display this:
it looks like I didn't install NordicSemiconductor.nRF_DeviceFamilyPack...
Hello,
I use a nRF52832 device, and I have some strange behavior when I use PWM. You can see my test program listed below.
Thank for your reply, Thierry!
/*
* Test_PWM...
Hi. I am a newbie in Nordic chips, quite knowledgeable in Atmel AVR, though. I'm working with an nRF51822 on a board like this www.waveshare.com/.../BLE400 . I use the Mbed...
This might seem like a really banal question, but i could need some clarification on this.
My understanding is that the config_client should be used on the network provisioner...
I want to connect a ST Chip (LSM6DSL - Datasheet ) via SPI with the nRF52840 Preview DK (SDK13) - NRF_DRV_SPI_MODE_0
When I am using the SPI Master example with different...
