Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
hi,
I have created shared channel. currently I only have one master and one slave working.
Master is sending data to slave and it s working perfectly.
But I can not...
Hello,
i haven't found an answer to this question. Which address uses the PTX in Enhanced Shock Burst Protocol (nrf52832, SDK 11)? In the code I found only that:
NRF_RADIO...
Hi
According to the BT spec v4.2, Volume 6, section 4.5:-
"There shall be only one connection between two LE device addresses.
An initiator shall not send a connection...
As show in the title, suppose I have my own bluetooth stack implementation, Is there any possible to flash the bluetooth stack into the nordic series?
Or, another question...
Hello
I'm able to use the MasterEmulator in a WPF or command line application but when I try to use it in Windows PowerShell i get an error.
I'm trying (with the dll...
Hello,
We've been struggling for a while trying to understand how to interpret the nRF52832 electrical specification . Sorry if this may sound like a bad question but we...
Hi, I'm using SDK12 and I'm trying to implement button debouncing. I have initialized one of the nRF52 board buttons using app_buttons.c. In the infocenter I read that debouncing...
Hi!,
I have load Sniffer_firmware into PCA10028 and works, but I can load Sniffer_firmware into PCA10040? it's compatible?
This file --> ble-sniffer_nRF51822_1.0.1_1111_Sniffer...
Hi,
I have tested mbed Classic and mbed OS with CLI and Yotta and works with nRF51-DK and nRF52-DK. Also with Eclipse Neon.1 with yotta build Eclipse CDT4 - Ninja.
But...
Hi,
I have a JLINK EDU and JLINK LITE and an nRF52 module and am attempting to use nrfjprog to program the device. Both devices are able to erase the chip, but the JLINK...
