Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hello,
I have custom board with nRF52832, and I want to have possibility to DFU over UART.
I tested example bootloader (nRF5_SDK_11.0.0\examples\dfu\bootloader\pca10040...
I am using nrf51 SDK v.12.1.
And I found NRF_LOG_INFO("BLINKY START\n");
where can I find this log?
Is this different from SEEGER_WriteString or something?
Hi
We are using "gcc compiler" to compiler our programs. To download our programs we use "nRFgo Studio" app.
From the above image, when we load SDK into the device...
Hello,
Consider this scenario:
The client successfully writes to a characteristic by the application code can't use the data sent so it would be usefull to signal the...
Hello,everyone. Now i have the board nrf52832 and i want it to enter the low-power mode but keep the the advertising. Now the measured current is 160uA, I think there should...
Dear All,
I apologize in advance if it seems that the question has been already posed but it is still unclear to me.
I have a pin (SIG_OK) and I want to read its logic value...
On the nRF51 DK there is a MM8130-2600 connector. I suppose it is used for connecting coax cable when tuning the antenna(?)
The connector is quite expensive, though. Is...
Per the name "UUID" and the very limited background knowledge that I have, it appears that a particular device can have its UUID assigned by its manaufacture, who bought the...
Hello.
I am developing a BLE application on NRF52832 using Nordic SDK11 and S132 softdevice. I use Linux PC as a BLE host device, and can pair & bond the NRF bluetooth...
Hi there! I'm using the nRF Toolbox's UART to test the receiving of my data stream. I'm trying to send a data array collected (from spi) in my main loop and send it via UART...
I am studying the iot-sdk of nordic.
Now, as I have shown in previous questions, I can not detect the device under the linux system according to the toturial in iot.
Now...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1?
About problem:
...
Hi,
I've been trying to add the option for BLE HID to the Espruino JS interpreter on nRF52 - it's something that ideally would be switchable at runtime.
After having...
Dear All
In my application we could not use the ADC inside the nRF51822 because 10bit are under our requirements. But now with the new nRF52xxx with a built-in 12bit ADC...
Did anyone manage to build project on Eclipse with some nRF52 BLE application for HomeKit?
I have found only one project from aanon4 but I cannot even build it.
Sometimes...
